This document establishes a classification for phenolic and aminoplastic polycondensation adhesives classified according to EN 301, one component polyurethane adhesives classified according to EN 15425 and emulsion polymer isocyanate adhesives classified according to EN 16254, according to their suitability for use for load-bearing timber structures made of selected hardwood species (group A) in defined climatic exposure conditions; it specifies performance requirements for such adhesives for the factory manufacture or factory-like manufacturing conditions of load-bearing timber structures made of selected hardwood species only, with no specific high shear strength classification.
NOTE An adhesive with high shear strength classification is needed when the declared characteristic shear strength of the glued laminated product is above 3,5 N/mm2, which is the declared characteristic shear strength of glulam made of softwoods according to EN 14080:2013 Table 4. See prEN 18307-3 requirements in this case.
It also classifies aminoplastic adhesive systems being used with a range of hardener dosage, and one component polyurethane adhesive product lines where all the products within the line have the same chemical composition except for a different amount of catalyst.
This document only specifies the performance of an adhesive for use in an environment corresponding to the defined conditions.
The performance requirements of this document are applicable to the adhesive only, not to the manufacturing timber products. This document does not cover the performance of adhesives for on-site gluing (except for factory-like conditions) nor the production of wood-based panels, except solid wood panels, or modified and stabilized wood with considerably reduced swelling and shrinkage properties, e.g. such as acetylated wood, heat treated wood and polymer impregnated wood. It also does not cover preservative treated wood.
This document is primarily intended for use by adhesive manufacturers and for use in timber products made of selected hardwood species bonded with adhesives, to assess or control the quality of adhesives. The requirements apply to the type testing of the adhesives. Production control activities are outside the scope of this document.
Adhesives meeting the requirements of this document are adequate for use in a load-bearing timber products made of selected hardwood species, provided that the bonding process has been carried out according to an appropriate product standard.
Selected hardwood species covered by this document are listed in FprCEN/TS XXX , group A. FprCEN/TS XXX also specifies nominal physical properties of the mentioned species that are used for testing according to this document.
Registration number (WIID)
74602
Scope
This document establishes a classification for phenolic and aminoplastic polycondensation adhesives classified according to EN 301, one component polyurethane adhesives classified according to EN 15425 and emulsion polymer isocyanate adhesives classified according to EN 16254, according to their suitability for use for load-bearing timber structures made of selected hardwood species (group A) in defined climatic exposure conditions; it specifies performance requirements for such adhesives for the factory manufacture or factory-like manufacturing conditions of load-bearing timber structures made of selected hardwood species only, with no specific high shear strength classification.
NOTE An adhesive with high shear strength classification is needed when the declared characteristic shear strength of the glued laminated product is above 3,5 N/mm2, which is the declared characteristic shear strength of glulam made of softwoods according to EN 14080:2013 Table 4. See prEN 18307-3 requirements in this case.
It also classifies aminoplastic adhesive systems being used with a range of hardener dosage, and one component polyurethane adhesive product lines where all the products within the line have the same chemical composition except for a different amount of catalyst.
This document only specifies the performance of an adhesive for use in an environment corresponding to the defined conditions.
The performance requirements of this document are applicable to the adhesive only, not to the manufacturing timber products. This document does not cover the performance of adhesives for on-site gluing (except for factory-like conditions) nor the production of wood-based panels, except solid wood panels, or modified and stabilized wood with considerably reduced swelling and shrinkage properties, e.g. such as acetylated wood, heat treated wood and polymer impregnated wood. It also does not cover preservative treated wood.
This document is primarily intended for use by adhesive manufacturers and for use in timber products made of selected hardwood species bonded with adhesives, to assess or control the quality of adhesives. The requirements apply to the type testing of the adhesives. Production control activities are outside the scope of this document.
Adhesives meeting the requirements of this document are adequate for use in a load-bearing timber products made of selected hardwood species, provided that the bonding process has been carried out according to an appropriate product standard.
Selected hardwood species covered by this document are listed in FprCEN/TS XXX , group A. FprCEN/TS XXX also specifies nominal physical properties of the mentioned species that are used for testing according to this document.
