8. Scope
This document specifies the general safety requirements for cold rolling mills for flat products.
This document is applicable to: Plant used for the manufacturing of metal cold rolled flat products from the material supply from entry (1), via the mill stand(s) (2) with roll changing devices (4), to the material removal (3) (see Figure 1).
This standard does not cover:
Thermo process equipment, e.g., in accordance with EN 746 series;
Strip processing lines according to EN 15061, e.g., pickling line;
Abrasive blasting plants according to EN 1248;
Coil transporting system before coil take-over-point at the entry section and after coil take-over-point at the exit section, e.g., hook conveyors, overhead cranes, fork lift and railway trucks and other vehicles;
Roll shop equipment;
Hook conveyors according to EN 619;
Non-fixed load lifting attachments, e.g., according to EN 13155;
Storage equipment (e.g., high-bay warehouses);
Cranes, fork lifts, trucks and railway trucks and other vehicles;
Process technology (e.g., systems for rolling lubricant, compressed air, treatment of water, cleaning system for exhaust air);
Firefighting system.
NOTE Special requirements for protection of persons in case of using asphyxiant gases used in firefighting system is covered by this document, see Annex C.
This document deals with foreseeable significant hazards, hazardous situations and events relevant to cold rolling mills for flat products, when used as intended and under conditions of misuse which are reasonably foreseeable by the manufacturer. It provides the requirements to be met by the manufacturer to ensure the safety of persons and property during transport, commissioning, operation and de-commissioning, as well as in the event of foreseeable failures or malfunctions that can occur in the equipment.
The foreseeable significant hazards include hazards due to:
Movement of machinery and workpieces;
Ejection of material;
Escape of liquids and gases;
Inadequacy of the mechanical strength;
Hydraulic and pneumatic;
Fire;
Contact with hot parts and hazardous substances;
Breathing of hazardous substances;
Noise and vibration;
Ionizing radiation;
Thermal heat radiation.
The corresponding significant hazards are listed in informative Annex H.
NOTE For modernization, it is recommended to apply this document (C-type standard) for the part to be modernized.
Registration number (WIID)
68965
Scope
8. Scope
This document specifies the general safety requirements for cold rolling mills for flat products.
This document is applicable to: Plant used for the manufacturing of metal cold rolled flat products from the material supply from entry (1), via the mill stand(s) (2) with roll changing devices (4), to the material removal (3) (see Figure 1).
This standard does not cover:
Thermo process equipment, e.g., in accordance with EN 746 series;
Strip processing lines according to EN 15061, e.g., pickling line;
Abrasive blasting plants according to EN 1248;
Coil transporting system before coil take-over-point at the entry section and after coil take-over-point at the exit section, e.g., hook conveyors, overhead cranes, fork lift and railway trucks and other vehicles;
Roll shop equipment;
Hook conveyors according to EN 619;
Non-fixed load lifting attachments, e.g., according to EN 13155;
Storage equipment (e.g., high-bay warehouses);
Cranes, fork lifts, trucks and railway trucks and other vehicles;
Process technology (e.g., systems for rolling lubricant, compressed air, treatment of water, cleaning system for exhaust air);
Firefighting system.
NOTE Special requirements for protection of persons in case of using asphyxiant gases used in firefighting system is covered by this document, see Annex C.
This document deals with foreseeable significant hazards, hazardous situations and events relevant to cold rolling mills for flat products, when used as intended and under conditions of misuse which are reasonably foreseeable by the manufacturer. It provides the requirements to be met by the manufacturer to ensure the safety of persons and property during transport, commissioning, operation and de-commissioning, as well as in the event of foreseeable failures or malfunctions that can occur in the equipment.
The foreseeable significant hazards include hazards due to:
Movement of machinery and workpieces;
Ejection of material;
Escape of liquids and gases;
Inadequacy of the mechanical strength;
Hydraulic and pneumatic;
Fire;
Contact with hot parts and hazardous substances;
Breathing of hazardous substances;
Noise and vibration;
Ionizing radiation;
Thermal heat radiation.
The corresponding significant hazards are listed in informative Annex H.
NOTE For modernization, it is recommended to apply this document (C-type standard) for the part to be modernized.
