CEN/TC 155

Projekta Nr.FprCEN/TS 12201-7
NosaukumsThis document gives guidance and requirements for the assessment of conformity of compounds, products, joints and assemblies in accordance with the applicable part(s) of EN 12201 intended to be included in the manufacturer’s quality plan as part of the quality management system and for the establishment of certification procedures. NOTE 1 A test matrix provides an overview of the testing scheme in Annex C, Table C.1. NOTE 2 If certification is involved, the certification bodies and inspection bodies operating in accordance with EN ISO/IEC 17065 [6] and EN ISO/IEC 17020 [4] are considered to be competent. Socket fusion fittings according to EN 12201 3:2024, Annex A, and mechanical fittings according to ISO 17885 are not covered in this document. In conjunction with EN 12201 1, EN 12201 2, EN 12201 3, EN 12201 4 and EN 12201 5, this document is applicable to polyethylene (PE) pressure piping systems (mains and service pipes) for buried or above ground applications, intended for the conveyance of water for human consumption, raw water prior to treatment, drains and sewers under pressure, vacuum sewer systems, and water for other purposes, with the exception of industrial application. The intended use includes sea outfalls, laid in water and pipes suspended below bridges. It is applicable to PE pipes, fittings, and valves, their joints and joints with components of PE and other materials intended to be used under the following conditions: a) allowable operating pressure, PFA, up to 25 bar ; b) an operating temperature of 20 °C as a reference temperature. NOTE 3 Industrial application is covered by EN ISO 15494 [3]. NOTE 4 For applications operating at constant temperature greater than 20 °C and up to and including 50 °C, see EN 12201 1:2024, Annex A. NOTE 5 It is the responsibility of the purchaser or specifier to make the appropriate selections from these aspects, taking into account their particular requirements and any relevant national guidance or regulations and installation practices or codes.
Reģistrācijas numurs (WIID)79023
Darbības sfēraThis document gives guidance and requirements for the assessment of conformity of compounds, products, joints and assemblies in accordance with the applicable part(s) of EN 12201 intended to be included in the manufacturer’s quality plan as part of the quality management system and for the establishment of certification procedures. NOTE 1 A test matrix provides an overview of the testing scheme in Annex C, Table C.1. NOTE 2 If certification is involved, the certification bodies and inspection bodies operating in accordance with EN ISO/IEC 17065 [6] and EN ISO/IEC 17020 [4] are considered to be competent. Socket fusion fittings according to EN 12201 3:2024, Annex A, and mechanical fittings according to ISO 17885 are not covered in this document. In conjunction with EN 12201 1, EN 12201 2, EN 12201 3, EN 12201 4 and EN 12201 5, this document is applicable to polyethylene (PE) pressure piping systems (mains and service pipes) for buried or above ground applications, intended for the conveyance of water for human consumption, raw water prior to treatment, drains and sewers under pressure, vacuum sewer systems, and water for other purposes, with the exception of industrial application. The intended use includes sea outfalls, laid in water and pipes suspended below bridges. It is applicable to PE pipes, fittings, and valves, their joints and joints with components of PE and other materials intended to be used under the following conditions: a) allowable operating pressure, PFA, up to 25 bar ; b) an operating temperature of 20 °C as a reference temperature. NOTE 3 Industrial application is covered by EN ISO 15494 [3]. NOTE 4 For applications operating at constant temperature greater than 20 °C and up to and including 50 °C, see EN 12201 1:2024, Annex A. NOTE 5 It is the responsibility of the purchaser or specifier to make the appropriate selections from these aspects, taking into account their particular requirements and any relevant national guidance or regulations and installation practices or codes.
StatussIzstrādē
ICS grupa23.040.05
91.140.60
23.040.03